At present, rural farmers choose vertical mixing equipment, but experts suggest that large-scale pig farms should choose horizontal mixers when selecting feed processing equipment. The equipment has high mixing efficiency, good mixing quality, short discharge time and residual amount. less. However, the following points should be noted when selecting and using a horizontal mixer:
1. Select the horizontal mixer according to the daily production volume. Because the processing time of each batch of material in the mixer is about 6 minutes, plus the time of discharging and feeding, the processing time of each batch of materials can be calculated in 10 minutes, then 6 batches can be processed in 1 hour. If you choose a mixer with a processing capacity of 100 kg per batch, you can process 600 kg per hour. Users can choose a horizontal mixer according to their needs.
2. According to the working principle of the horizontal spiral belt mixer, the ability of the double spiral belt for stirring and mixing to push the material in the opposite direction should be basically the same. Since the pitch of the inner spiral belt should be smaller than that of the outer spiral belt, the pitch of the inner spiral belt should be smaller than that of the outer spiral belt, and the width should be larger than the outer spiral belt, otherwise the material will be concentrated in one direction. Therefore, pay attention to this when selecting a horizontal mixer.
3. According to the design principle, the gap between the spiral belt and the casing in the spiral belt mixer can be 4 mm to 10 mm, and the material can be frictionally driven to participate in the mixing.
However, since the pulverization particle size and the friction coefficient of the material are not the same, the time for the materials of the various components to participate in the mixing is different, resulting in product non-uniformity. Some manufacturers have realized this and have improved the product. One is to pay attention to the processing precision, so that the bottom gap is reduced to 1 mm 2 mm; the other is to make the position between the main shaft and the housing adjustable, and the spiral belt and the housing can be adjusted frequently according to the amount of wear. Clearance. When choosing a mixer, these two forms of product should be a good choice.
4. Select the horizontal spiral belt mixer to pay attention to the discharge method.
The form of the large opening should be chosen. Do not choose the discharge form of the side opening or the small opening at the bottom. The reason is: when the mixer completes the mixing and mixing in the specified time, the zui can be cleared once in a short time to ensure the uniformity of the material; if the side opening or the bottom small opening spiral belt is gradually released, one will delay the time and fail to reach The expected productivity, the second is that the material has reached the good uniformity of the Zui, excessive stirring will cause the material to segregate, destroying the uniformity, thus losing the significance of using the horizontal mixer.
1. Select the horizontal mixer according to the daily production volume. Because the processing time of each batch of material in the mixer is about 6 minutes, plus the time of discharging and feeding, the processing time of each batch of materials can be calculated in 10 minutes, then 6 batches can be processed in 1 hour. If you choose a mixer with a processing capacity of 100 kg per batch, you can process 600 kg per hour. Users can choose a horizontal mixer according to their needs.
2. According to the working principle of the horizontal spiral belt mixer, the ability of the double spiral belt for stirring and mixing to push the material in the opposite direction should be basically the same. Since the pitch of the inner spiral belt should be smaller than that of the outer spiral belt, the pitch of the inner spiral belt should be smaller than that of the outer spiral belt, and the width should be larger than the outer spiral belt, otherwise the material will be concentrated in one direction. Therefore, pay attention to this when selecting a horizontal mixer.
3. According to the design principle, the gap between the spiral belt and the casing in the spiral belt mixer can be 4 mm to 10 mm, and the material can be frictionally driven to participate in the mixing.
However, since the pulverization particle size and the friction coefficient of the material are not the same, the time for the materials of the various components to participate in the mixing is different, resulting in product non-uniformity. Some manufacturers have realized this and have improved the product. One is to pay attention to the processing precision, so that the bottom gap is reduced to 1 mm 2 mm; the other is to make the position between the main shaft and the housing adjustable, and the spiral belt and the housing can be adjusted frequently according to the amount of wear. Clearance. When choosing a mixer, these two forms of product should be a good choice.
4. Select the horizontal spiral belt mixer to pay attention to the discharge method.
The form of the large opening should be chosen. Do not choose the discharge form of the side opening or the small opening at the bottom. The reason is: when the mixer completes the mixing and mixing in the specified time, the zui can be cleared once in a short time to ensure the uniformity of the material; if the side opening or the bottom small opening spiral belt is gradually released, one will delay the time and fail to reach The expected productivity, the second is that the material has reached the good uniformity of the Zui, excessive stirring will cause the material to segregate, destroying the uniformity, thus losing the significance of using the horizontal mixer.
Luminous Tape,Photoluminescent Stair Nosing,Stair Nosing,Glow In The Dark Stair Nosing
JINAN REALGLOW CO.,LTD , https://www.realglowsign.com